………….BLOW OUT SALE…Taylor Race Engineering SCCA Formula Enterprise Ring and Pinion. 12-33 . $600.00 while supply last  

Item #: INV-05101004
Price: $600.00

An alternative to the standard 86/94mm drive flanges found on the TRE Torque Biasing differential. These small tulip style falnges are a one piece design ,meaning the tri-pod housing and flange are now one unit.They are 2.5" O.D, and weigh 1 pound 4.3 onces.They are a direct replacement and will require a 02002074 boot.

Item #: INV-0200059401
Price: $255.00

SHOP MANUAL FOR THE TAYOR RACE ENGINEERING SERIES 26 SPRITE GEARBOX. ALSO WORKS FOR THE RICHMOND CONVERSION

Item #: INV-0200156
Price: $25.63

SCREW CAP PEDISTAL ATTACHMENT MK TYPE CASE

Item #: INV-020072
Price: $0.53

WASHER 7 MM

Item #: INV-0200721
Price: $0.21

SCREW FLT HD 5/16-18 X 1

Item #: INV-0200722
Price: $0.77

BOLTS, INPUT SEAL RETAINER PLATE

Item #: INV-0200723
Price: $0.26

CAP-SCREW TO ATTACH SAAB CYLINDER TO PEDESTAL. INPUT SNOUT/BEARING CARRIER BOLTS.

Item #: INV-020073
Price: $0.56

CAP SCREW 1/4 - 28 X 1.5"

Item #: INV-020074
Price: $0.72

PEDESTAL FOR LOTUS CARS WITH 3 3/8 in BELL HOUSING AND SINGLE PLATE RACING CLUTCH

Item #: INV-0200761
Price: $179.38

PEDESTAL FOR LOTUS CARS WITH 3 3/8 in BELL HOUSING AND TWO PLATE RACING CLUTCH

Item #: INV-02007611
Price: $179.38

PEDESTAL SET FOR TRE 350-901 FLYWHEEL/367-002 CLUTCH AND 361-8123 SLAVE CYLINDER. INCLUDES MACHINING OF SEAL RETAINER AND BOLTS

Item #: INV-02007612
Price: $179.38

PEDESTAL FT200 FOR RT4 WITH TWIN DISC CLUTCH USING TILTON 361-7775 CYLINDER

Item #: INV-0200762
Price: $205.00

PEDESTAL FT200 GENERIC FOR USE WITH 361-7775 1.7 in TALL SLAVE CYLINDER

Item #: INV-02007621
Price: $133.25

PEDESTAL FOR DATSUN 510/240Z WITH QUAIFE GEARBOX. SINGLE DISC CLUTCH

Item #: INV-0200763
Price: $179.38

PEDESTAL FOR USE IN FF1600 WITH STOCK CLUTCH. SAAB CYLINDER

Item #: INV-0200764
Price: $179.38

PEDESTAL SPRITE AND MIDGET WITH STOCK FRONT COVER RACE OR STOCK CLUTCH INCLUDES PEDISTAL STANDS 3

Item #: INV-0200765
Price: $205.00

PEDESTAL SWIFT DB6 FORMULA FORD 1600 7.25 in CLUTCH UTILIZING TILTON 361-8122 SLAVE CYLINDER.

Item #: INV-0200766
Price: $179.38

PEDESTAL SAAB 900 REPLACEMENT TO BE USED WITH INV-361-802 TILTON CYLINDER. CAUTION: SEE DRAWING FOR PROPER BEARING AND PISTON COMBINATIONS.

Item #: INV-0200767
Price: $133.25

PEDESTAL USED WITH ANNULAR CLUTCH CYLINDER. MK9/F3 CLUTCH FORMULA 2000

Item #: INV-020076A
Price: $112.75

PEDESTAL CUSTOM FOR SPECIAL SLAVE CYLINDER REQUIREMENTS

Item #: INV-020076AC
Price: $179.83

PEDESTAL FOR USE WITH MK9 GEARBOX WITH FORMULA 3 CLUTCH FITTED TO A FORMULA FORD 1600

Item #: INV-020076B
Price: $133.25

PEDESTAL FOR FF1600 WITH TILTON 7.25" OR 5.5" CLUTCH AND TILTON 361-802 OR 361-803 CYLINDER

Item #: INV-020076BT
Price: $205.00

PEDESTAL FOR RALT RT 5 ANNULAR SLAVE CYLINDER KIT SAAB CYLINDER

Item #: INV-020076C
Price: $205.00

PEDESTAL FOR '99-05VAN DIEMEN SLAVE CYLINDER KIT USING TILTON 361-772 SLAVE CYLINDER F2000 SINGLE PLATE CLUTCH

Item #: INV-020076D
Price: $179.38

PEDESTAL FOR '97-98 VAN DIEMEN SLAVE CYLINDER KIT USING TILTON 361-777 SLAVE CYLINDER F2000 SINGLE PLATE CLUTCH

Item #: INV-020076E
Price: $179.38

PEDESTAL FOR VAN DIEMEN; FF 1600 SINGLE PLATE CLUTCH AND F2000 ZTEC 2-PLATE CLUTCH 1999-2005 SLAVE CYLINDER KIT USING TILTON 361-8122/8123 SLAVE CYLINDER

Item #: INV-020076F
Price: $179.38

PEDESTAL RT41 USING TILTON 361-772 SLAVE CYLINDER KIT

Item #: INV-020076G
Price: $179.38

PEDESTAL RX8 TRE FW CLTCH PKG

Item #: INV-020076H
Price: $143.50

MK Series kits include the adapter, cylinder, release bearing for stock or 7-1/4" racing clutch, attaching screws, and line adapters. Hose ends and remote bleed kit must be ordered separately. Size of pressure line (-3 or -4) must be specified so that we can install the correct fitting in the cylinder. NOTE: This system is attached to the MK transmission with three bolts which thread into three holes encircling the main input shaft seal. If these three holes are missing in your case, a Custom annular slave cylinder system must be ordered.

Item #: INV-020077
Price: $430.00

MK Series kits include the adapter, cylinder, release bearing for stock or 7-1/4" racing clutch, attaching screws, and line adapters. Hose ends and remote bleed kit must be ordered separately. Size of pressure line (-3 or -4) must be specified so that we can install the correct fitting in the cylinder. NOTE: This system is attached to the MK transmission with three bolts which thread into three holes encircling the main input shaft seal. If these three holes are missing in your case, a Custom annular slave cylinder system must be ordered.

Item #: INV-0200771
Price: $430.00

 MK Series kits include the adapter, cylinder, release bearing for stock or 7-1/4" racing clutch, attaching screws, and line adapters. Hose ends and remote bleed kit must be ordered separately. Size of pressure line (-3 or -4) must be specified so that we can install the correct fitting in the cylinder. For the 5-1/2" or smaller clutch, the special Tilton piston and bearing must be ordered. NOTE: This system is attached to the MK transmission with three bolts which thread into three holes encircling the main input shaft seal. If these three holes are missing in your case, a Custom annular slave cylinder system must be ordered.

Item #: INV-020078
Price: $430.00

 MK Series kits include the adapter, cylinder, release bearing for stock or 7-1/4" racing clutch, attaching screws, and line adapters. Hose ends and remote bleed kit must be ordered separately. Size of pressure line (-3 or -4) must be specified so that we can install the correct fitting in the cylinder. For the 5-1/2" or smaller clutch, the special Tilton piston and bearing shown on Page 13 must be ordered. NOTE: This system is attached to the MK transmission with three bolts which thread into three holes encircling the main input shaft seal. If these three holes are missing in your case, a Custom annular slave cylinder system must be ordered.

Item #: INV-0200781
Price: $430.00

 MK Series kits include the adapter, cylinder, release bearing for stock or 7-1/4" racing clutch, attaching screws, and line adapters. Hose ends and remote bleed kit must be ordered separately. Size of pressure line (-3 or -4) must be specified so that we can install the correct fitting in the cylinder. For the 5-1/2" or smaller clutch, the special Tilton piston and bearing shown on Page 13 must be ordered. NOTE: This system is attached to the MK transmission with three bolts which thread into three holes encircling the main input shaft seal. If these three holes are missing in your case, a Custom annular slave cylinder system must be ordered.

Item #: INV-0200782
Price: $390.00

MK Series kits include the adapter, cylinder, release bearing for stock or 7-1/4" racing clutch, attaching screws, and line adapters. Hose ends and remote bleed kit must be ordered separately. Size of pressure line (-3 or -4) must be specified so that we can install the correct fitting in the cylinder. For the 5-1/2" or smaller clutch, the special Tilton piston and bearing shown on Page 13 must be ordered. NOTE: This system is attached to the MK transmission with three bolts which thread into three holes encircling the main input shaft seal. If these three holes are missing in your case, a Custom annular slave cylinder system must be ordered.

Item #: INV-0200783
Price: $500.00

MK Series kits include the adapter, cylinder, release bearing for stock or 7-1/4" racing clutch, attaching screws, and line adapters. Hose ends and remote bleed kit must be ordered separately. Size of pressure line (-3 or -4) must be specified so that we can install the correct fitting in the cylinder. For the 5-1/2" or smaller clutch, the special Tilton piston and bearing shown on Page 13 must be ordered. NOTE: This system is attached to the MK transmission with three bolts which thread into three holes encircling the main input shaft seal. If these three holes are missing in your case, a Custom annular slave cylinder system must be ordered.

Item #: INV-0200784
Price: $360.00

 Hydraulic release bearing kit for the Van Diemen 1999 through 2004 F2000 cars.Kit comes with all the fittings and steel braided line including a remote bleed.Tiltons newest low profile slave cylinder with only one seal is incorporated into this easy serviceable kit. PN#361-008 38mm contact bearing used with Tiltons 5.5'' clutch PN#361-031 44mm contact bearing used with Tilton/QM/AP 7.25'' clutch and 5.5'' QM and AP clutch

Item #: INV-0200786
Price: $565.00

Hydraulic release bearing kit for the Van Diemen 1997 through 1998 F2000 cars.Kit comes with all the fittings and steel braided line including a remote bleed.Tiltons newest low profile slave cylinder with only one seal is incorporated into this easy serviceable kit. PN#361-008 38mm contact bearing used with Tiltons 5.5'' clutch PN#361-031 44mm contact bearing used with Tilton/QM/AP 7.25'' clutch and 5.5'' QM and AP clutch

Item #: INV-0200787
Price: $565.00

A simple bearing insert will make it possible to run a Quarter Master V drive ,or AP clutch. Hydraulic release bearing kit for the Van Dieman 1999/2004 FF1600 single disc Tilton OT 2 7.25 clutch.Will also work with the F2000 twin disc 7.25 .Kit comes with all the hardware including a remote bleed line.This kit can only be used in a Formula Ford application with a Quarter Master V drive clutch if the flywheel friction surface is a stock Ford dimension of 2.025" measured from the back of the engine block.

Item #: INV-0200788
Price: $565.00

 Slave cylinder kit for F2000 2 disc 5.5" And FF single disc 5.5 Tilton OT2 clutch

Item #: INV-0200789
Price: $565.00

 Hose ends and remote bleed kit must be ordered separately. Size of pressure line (-3 or -4) must be specified so that we can install the correct fitting in the cylinder.

Item #: INV-020078C
Price: $450.00

ANNNULAR SLAVE CYLINDER KIT CUSTOM USING TILTON SLAVE CYLINDER

Item #: INV-020078CT
Price: $699.00

Replaces the expensive Ralt RT-4 annular slave cylinder with the modern cylinder used in RT 40/41 cars. Requires modification of input shaft housing and re-plumbing. AN-3 hose-to-cylinder adapters and release bearing for 7-1/4" racing clutch are included. These kits fit the standard RT4 and other FT-equipped cars using the 2 1/4" adapter ring and Cosworth motor with metallic clutches. Carbon clutches require a custom installation.

Item #: INV-020079
Price: $515.00

Annular clutch release system utilizing Tilton slave cylinder. For use with Sprite/Midget transmissions with stock front cover. This system completely replaces the troublesome stock lever and carbon bearing. Specify 7.25" or 5.5" racing clutch

Item #: INV-0200791
Price: $535.00

 W/TWO DISC CLUTCH. USES TILTON SLAVE CYLINDER

Item #: INV-0200793
Price: $499.00

Use stiff spring for 4-speed. Use soft spring for 5-speed. Hewland Part #FT2032

Item #: INV-040030
Price: $3.41

1/R STOP TUBE

Item #: INV-040301
Price: $11.28

SPACING SHIM .032"

Item #: INV-040310
Price: $0.21

SPACING SHIM .010"

Item #: INV-040320
Price: $2.05

SPACING SHIM .005"

Item #: INV-040321
Price: $2.05

YOUR CART

There are no products in your shopping cart.

0 Items $0.00

ITEMS VIEWED

Nothing has been read yet.